526-2037 5262037 Excavator Fuel Pump Replacement Part for E320GC E336GC E345GC Machine
Product Details
| Part Number: | 526-2037 / 5262037 | MOQ: | 1 |
|---|---|---|---|
| Highlight |
Excavator Fuel Pump Replacement Part,526-2037 Fuel Pump for E320GC,Diesel Fuel Pump E336GC E345GC |
||
Product Description
The 526-2037 (5262037) Fuel Pump Assembly is a high-quality replacement part engineered for optimal performance and fuel efficiency in E320GC, E336GC, and E345GC construction machinery. Manufactured by JIAJUE, this brand-new fuel pump delivers reliable fuel delivery and long service life under demanding job-site conditions.
| Product Name | Fuel Pump |
|---|---|
| Part Number | 526-2037 / 5262037 |
| Brand Name | JIAJUE |
| Compatible Models | E320GC / E336GC / E345GC |
| Condition | Brand New |
| Availability | Rich Stock |
| Approximate Weight | 10 KG |
| Size (per unit) | 20 cm x 5 cm x 8 cm |
| Delivery Methods | DHL, FedEx, TNT, UPS |
| Warranty | 3 Months |
| Shipment | Dispatched within 24–48 hours |
Each 526-2037 fuel pump undergoes rigorous quality inspection before shipment to ensure dimensional accuracy, sealing integrity, and reliable fuel delivery performance.
How do I install my fuel injector after purchasing it?
Please refer to the "Step-by-Step Installation Guide" on our product details page for detailed installation instructions.
What precautions should I take before installing my fuel injector?
The installation environment must be dust-free. Lubricate the O-ring with clean machine oil before installation to prevent cutting, and ensure the O-ring is installed correctly.
Why is my engine still unusable after replacing the fuel injector?
This is common due to air trapped in the high-pressure oil rail. Cycle the engine in short bursts (no more than 30 seconds) to purge air. It may take several attempts to stabilize pressure.
Is my device compatible with this part number of fuel injectors?
If unsure about compatibility, send us your Engine Serial Number (ESN) for free verification.
How to determine if your fuel injectors need replacing?
- Cylinder Cut-out Test: Using diagnostic software (ET), shut off cylinders one by one and observe engine speed fluctuations.
- Fuel Rail Pressure Test: Check for internal leaks preventing the system from building critical starting pressure.
- Back-leakage Test: Excessive back-leakage indicates severe wear of the internal control valve assembly.
- Visual Inspection: Inspect fuel injector nozzles for carbon buildup, blockage, or corrosion.
How long will it take to receive my package after payment?
Delivery time depends on your country, region, and customs clearance. Contact us with your address and postal code for shipping costs and estimated delivery time.
HEUI (Hydraulic Electronic Unit Injection) systems are extremely sensitive to contamination. A single speck of dust can cause premature failure.
- Preparation: Clean the injector bores thoroughly. Ensure no carbon debris, old O-rings, or fuel/oil residue at the bottom of the seat. Inspect the injector sleeve for pitting or erosion.
- Lubrication: Apply clean engine oil to the three O-rings and backup rings. Never use grease — only clean engine oil ensures seals slide in without tearing.
- Seating the Injector: Push the injector down firmly by hand until you feel it "seat." Install the hold-down clamp and bolt.
- Torque Specifications: Tighten the bolt to 30 N⋅m ± 7 N⋅m (22 lb-ft). Note: Over-tightening can crack the injector body; under-tightening causes combustion gas leakage.
- Trim Code Programming: Locate the 6-digit alphanumeric code on the top of the injector solenoid. Use ET (Electronic Technician) software to program this code into the ECM for precise fuel delivery synchronization.
| Issue | Root Cause | Solution |
|---|---|---|
| Black Smoke | Poor spray atomization or stuck needle valve causing dripping | Inspect the air filter |
| Hard Start | Internal leakage in injector leading to insufficient starting oil pressure | Inspect injector O-rings and internal seals |
| Engine Misfire | Faulty solenoid valve coil or worn internal valve components | Inspect wiring harness connections and replace damaged injectors |
Product Highlights
526-2037 Excavator Fuel Pump for E320GC / E336GC / E345GCThe 526-2037 (5262037) Fuel Pump Assembly is a high-quality replacement part engineered for optimal performance and fuel efficiency in E320GC, E336GC, and E345GC construction machinery. Manufactured by JIAJUE, this brand-new fuel pump delivers ...
262-2878 Controller ECU 2622878 For C15 C18 Engine Parts
262-2878 Controller ECU 2622878 For C15 C18 Engine Parts Product Name: Controller Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 262-2878 MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen/Ningbo/Shanghai Delivery Methods: ...
160-1758 1601758 Controller ECU For D6R Loader
160-1758 1601758 Controller ECU For D6R Loader Product introduction Product Name: ECU Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 160-1758 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen/Ningbo...
134-6553 1346553 ECU ECM Controller For 120H Wheel Loader
134-6553 1346553 ECU ECM Controller For 120H Wheel Loader Product introduction Product Name: ECU Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 134-6553 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou...
243-3820 2433820 Monitor Panel For C11 Engine
243-3820 2433820 Monitor Panel For C11 Engine Product introduction Product Name: Monitor Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 243-3820 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen...
Please use our online inquiry contact form below if you have any questions, our team will get back to you as soon as possible.
