2999119 299-9119 Control Lever Handle Pilot Valve Loader Part for E242B 252B 236B 267B Loader
Product Details
| Part Number: | 2999119 / 299-9119 | MOQ: | 1 |
|---|---|---|---|
| Highlight |
Control Lever Handle Pilot Valve,Loader Part for E242B 252B,Pilot Valve Loader Handle Part |
||
Product Description
The 2999119 / 299-9119 Control Lever Handle Pilot Valve is a high-quality replacement component engineered for E242B, 252B, 236B, and 267B Loader applications. Built to deliver precise hydraulic control, consistent performance, and reliable operation, it is a dependable solution for industrial and heavy-duty machinery, including the E242B, 252B, 236B, and 267B Loader series.
| Product Name | Control Lever Handle Pilot Valve |
|---|---|
| Part Number | 2999119 / 299-9119 |
| Brand Name | JIAJUE |
| Model | E242B 252B 236B 267B Loader |
| Condition | Brand New |
| Availability | Rich Stock |
| Approximate Weight | 2 KG |
| Size (per unit) | 20 cm x 5 cm x 8 cm |
| Delivery Methods | DHL, FedEx, TNT, UPS |
| Warranty | 3 Months |
| Shipment | Dispatched within 24–48 hours |
Please refer to the "Step-by-Step Installation Guide" below for detailed installation instructions.
The installation environment must be dust-free. Lubricate the O-ring with clean machine oil before installation to prevent cutting, and ensure the O-ring is installed correctly.
This is common due to air trapped in the high-pressure oil rail. Cycle the engine in short bursts (no more than 30 seconds) to purge air. It may take several attempts to stabilize pressure.
If unsure about compatibility, send us your Engine Serial Number (ESN) for free verification.
- Cylinder Cut-out Test: Using diagnostic software (ET), shut off cylinders one by one and observe engine speed fluctuations.
- Fuel Rail Pressure Test: Check for internal leaks preventing the system from building critical starting pressure.
- Back-leakage Test: Excessive back-leakage indicates severe wear of the internal control valve assembly.
- Visual Inspection: Inspect fuel injector nozzles for carbon buildup, blockage, or corrosion.
Delivery time depends on your country, region, and customs clearance. Contact us with your address and postal code for shipping costs and estimated delivery time.
HEUI (Hydraulic Electronic Unit Injection) systems are extremely sensitive to contamination. A single speck of dust can cause premature failure.
- Preparation: Clean the injector bores thoroughly. Ensure no carbon debris, old O-rings, or fuel/oil residue at the bottom of the seat. Inspect the injector sleeve for pitting or erosion.
- Lubrication: Apply clean engine oil to the three O-rings and backup rings. Never use grease — only clean engine oil ensures seals slide in without tearing.
- Seating the Injector: Push the injector down firmly by hand until you feel it "seat." Install the hold-down clamp and bolt.
- Torque Specifications: Tighten the bolt to 30 N⋅m ± 7 N⋅m (22 lb-ft). Note: Over-tightening can crack the injector body; under-tightening causes combustion gas leakage.
- Trim Code Programming: Locate the 6-digit alphanumeric code on the top of the injector solenoid. Use ET (Electronic Technician) software to program this code into the ECM for precise fuel delivery synchronization.
| Issue | Root Cause | Solution |
|---|---|---|
| Black Smoke | Poor spray atomization or stuck needle valve causing dripping | Inspect the air filter |
| Hard Start | Internal leakage in injector leading to insufficient starting oil pressure | Inspect injector O-rings and internal seals |
| Engine Misfire | Faulty solenoid valve coil or worn internal valve components | Inspect wiring harness connections and replace damaged injectors |
Video demonstration: installation and operation of the diesel fuel injector for QSB6.7 engine applications.
Product Highlights
Product Overview The 2999119 / 299-9119 Control Lever Handle Pilot Valve is a high-quality replacement component engineered for E242B, 252B, 236B, and 267B Loader applications. Built to deliver precise hydraulic control, consistent performance, and reliable operation, it is a dependable solution for ...
262-2878 Controller ECU 2622878 For C15 C18 Engine Parts
262-2878 Controller ECU 2622878 For C15 C18 Engine Parts Product Name: Controller Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 262-2878 MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen/Ningbo/Shanghai Delivery Methods: ...
160-1758 1601758 Controller ECU For D6R Loader
160-1758 1601758 Controller ECU For D6R Loader Product introduction Product Name: ECU Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 160-1758 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen/Ningbo...
134-6553 1346553 ECU ECM Controller For 120H Wheel Loader
134-6553 1346553 ECU ECM Controller For 120H Wheel Loader Product introduction Product Name: ECU Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 134-6553 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou...
243-3820 2433820 Monitor Panel For C11 Engine
243-3820 2433820 Monitor Panel For C11 Engine Product introduction Product Name: Monitor Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 243-3820 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen...
Please use our online inquiry contact form below if you have any questions, our team will get back to you as soon as possible.
