XJAF-02679 Diesel Fuel Injector for R140LC-7A Excavator
Product Details
| Part Number: | XJAF-02679 | MOQ: | 1 |
|---|---|---|---|
| Highlight |
Diesel fuel injector for R140LC-7A,Excavator diesel injector with warranty,R140LC-7A fuel injector replacement |
||
Product Description
High-quality diesel fuel injector designed specifically for Excavator R140LC-7A models, ensuring optimal performance and reliability.
| Product Name | Fuel Injector |
|---|---|
| Part Number | XJAF-02679 |
| Brand Name | JIAJUE |
| Model | R140LC-7A |
| Availability | Rich Stock |
| Approximate Weight | 2KG |
| Size (for 1pc) | 20cm x 5cm x 8cm |
| Delivery Methods | DHL FedEx TNT UPS |
| Warranty | 3 months |
| Shipment | Dispatched within 24-48 hours |
Please refer to the "Step-by-Step Installation Guide" on our product details page, which contains very detailed installation instructions for how to install the injector.
The installation environment must be dust-free; the O-ring must be lubricated with clean machine oil before installation to prevent oil leakage caused by cutting the O-ring during installation; and remember to check that the O-ring is installed correctly.
This is common, due to air trapped in the high-pressure oil rail. Please cycle the engine in short bursts (no more than 30 seconds) to purge air. It may take several attempts to stabilize the pressure.
If you're not sure if this fits your machine, please send us your Engine Serial Number (ESN) for free verification.
- Cylinder Cut-out Test: Using diagnostic software (ET), cylinders are shut off one by one, and engine speed fluctuations are observed to locate the faulty cylinder.
- Fuel Rail Pressure Test: Check for internal leaks that prevent the system from building up the critical pressure required for starting.
- Back-leakage Test: Excessive back-leakage usually indicates severe wear of the internal control valve assembly.
- Visual Inspection: Inspect the fuel injector nozzles for carbon buildup, blockage, or corrosion.
This depends on your country and region, and the customs clearance time in your country. Please feel free to contact us and send us your address and postal code so we can check shipping costs and estimate delivery time for you.
HEUI (Hydraulic Electronic Unit Injection) systems are extremely sensitive to contamination. A single speck of dust can cause premature failure.
- Preparation: Clean the injector bores thoroughly. Ensure there is no carbon debris, old O-rings, or fuel/oil residue at the bottom of the seat. Inspect the injector sleeve for any signs of pitting or erosion.
- Lubrication: Apply clean engine oil to the three O-rings and the backup rings. Warning: Never use grease. Only use clean engine oil to ensure the seals slide in without tearing.
- Seating the Injector: Push the injector down firmly by hand until you feel it "seat." Install the hold-down clamp and bolt.
- Torque Specifications: Tighten the bolt to 30 N⋅m±7 N⋅m (22 lb-ft). Note: Over-tightening can crack the injector body; under-tightening causes combustion gas leakage.
- Trim Code Programming: Locate the 6-digit alphanumeric code on the top of the injector solenoid. Use ET (Electronic Technician) software to program this code into the ECM to ensure precise fuel delivery synchronization.
| Issue | Root Cause | Solution |
|---|---|---|
| Black Smoke | Poor spray atomization or a stuck needle valve can cause dripping. | Inspect the air filter. |
| Hard Start | Internal leakage in the injector can lead to insufficient starting oil pressure. | Inspect the injector O-rings and internal seals. |
| Engine Misfire | A faulty solenoid valve coil or worn internal valve components can cause this. | Inspect the wiring harness connections and replace any damaged injectors. |
Product Highlights
XJAF-02679 Diesel Fuel Injector for R140LC-7A ExcavatorHigh-quality diesel fuel injector designed specifically for Excavator R140LC-7A models, ensuring optimal performance and reliability.Product SpecificationsProduct NameFuel InjectorPart NumberXJAF-02679Brand NameJIAJUEModelR140LC-7AAvailabilityRi...
262-2878 Controller ECU 2622878 For C15 C18 Engine Parts
262-2878 Controller ECU 2622878 For C15 C18 Engine Parts Product Name: Controller Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 262-2878 MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen/Ningbo/Shanghai Delivery Methods: ...
160-1758 1601758 Controller ECU For D6R Loader
160-1758 1601758 Controller ECU For D6R Loader Product introduction Product Name: ECU Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 160-1758 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen/Ningbo...
134-6553 1346553 ECU ECM Controller For 120H Wheel Loader
134-6553 1346553 ECU ECM Controller For 120H Wheel Loader Product introduction Product Name: ECU Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 134-6553 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou...
243-3820 2433820 Monitor Panel For C11 Engine
243-3820 2433820 Monitor Panel For C11 Engine Product introduction Product Name: Monitor Place of Origin: GUNZGHOU Brand Name: JIAJUE Part Number: 243-3820 Type: Excavator Parts MOQ 1 Piece Condition: Brand New Availability: Rick Stock Supply Ability: 1000pcs Per Month Port: Guangzhou/Shenzhen...
Please use our online inquiry contact form below if you have any questions, our team will get back to you as soon as possible.
